🎓 शैक्षणिक योग्यता / पात्रता (Detailed
Eligibility Criteria – Trade-wise)
इस भर्ती
में ITI, Diploma और Degree तीनों प्रकार की योग्यताएँ मान्य हैं। नीचे
प्रत्येक ट्रेड के लिए विस्तृत
पात्रता, अनुभव, और महत्वपूर्ण शर्तें स्पष्ट रूप से दी गई हैं।
📌 महत्वपूर्ण नोट (सभी ट्रेड के लिए लागू):
- अभ्यर्थी
के पास NCVT/SCVT से
मान्यता प्राप्त ITI होना
चाहिए।
- Diploma / Degree AICTE/UGC से मान्यता प्राप्त संस्थान से होनी चाहिए।
- अंतिम
वर्ष के छात्र पात्र नहीं होंगे।
- योग्यता
और ट्रेड का मिलान अनिवार्य है।
📐 8. Mathematics /
Drawing Instructor
वेतनमान
₹ 32,800 – 1,03,600
शैक्षणिक
योग्यता
(क) हाई
स्कूल अथवा समकक्ष अथवा पुरानी पद्धति से 11वीं
कक्षा उत्तीर्ण, साथ ही सभी संबंधित पदों के लिए संबंधित ट्रेड में NCVT/SCVT
से मान्यता प्राप्त AITT (आई.टी.आई.) / NAC (शिक्षुता) परीक्षा उत्तीर्ण।
अथवा
(ख) AICTE/UGC से मान्यता प्राप्त किसी
विश्वविद्यालय/बोर्ड/संस्थान से निम्नलिखित विषयों में इंजीनियरिंग/टेक्नोलॉजी में स्नातक उपाधि अथवा किसी पॉलीटेक्निक से डिप्लोमा उत्तीर्ण:
- मैकेनिकल
इंजीनियरिंग
- मैकेनिकल
इंजीनियरिंग (प्रोडक्शन)
- मैकेनिकल
इंजीनियरिंग (इंडस्ट्रीज इंटीग्रेटेड)
- प्रोडक्शन
इंजीनियरिंग
- इंडस्ट्रियल
इंजीनियरिंग
- मैन्युफैक्चरिंग
इंजीनियरिंग
- इंडस्ट्रियल
प्रोडक्शन
- प्रोडक्शन
एंड मैन्युफैक्चरिंग
- मैकेनिकल
(टूल एंड डाई)
- मैकेनिकल
(वेल्डिंग एवं शीट मेटल)
- मैकेनिकल
(RAC)
- इंडस्ट्रियल
इंजीनियरिंग एंड मैनेजमेंट
· Syllabus for Training Officer (Maths/Drawing)
· Workshop CALCULATION & SCIENCE and ENGINEERING DRAWING:
· Paper code -08 (Post code 15 & 16)
· Unit, Fractions 1 Classification of Unit System 2 Fundamental and Derived Units F.P.S, C.G.S, M.K.S and SI Units 3 Measurement Units and Conversion 4 Factors, HCF, LCM and Problems 5 Fractions - Addition, Subtraction, Multiplication and Division 6 Decimal Fractions --Addition, Subtraction, Multiplication and Division, Solving Problems by using calculator
II. Square Root: Ratio and Proportions, Percentage, 1 Square and Square Root 2 Simple problems using calculator 3 Application of Pythagoras Theorem and related problems 4 Ratio and Proportions 5 Direct and Indirect proportion 6 Percentage 7 Changing percentage to decimal
III. Material Science: 1 Types of metals 2 Physical and Mechanical Properties of metals 3 Types of ferrous and non- ferrous metals 4 Introduction of iron and cast iron 5 Difference between iron and steel, alloy steel and carbon steel 6 Properties and uses of rubber, timber and insulating materials
IV. Mass, Weight, Volume, and Density: 1 Mass, volume, density, weight & specific gravity 2 Related problems for mass, volume, density, weight & specific gravity
V. Speed and Velocity, Work Power and Energy: 1 Rest, motion, speed, velocity, difference between speed and velocity, acceleration and retardation 2 Related problems on speed and velocity 3 Potential energy, Kinetic Energy and related problems with related problems 4 Work, power, energy, HP, IHP, BHP and efficiency
VI. Heat & Temperature and Pressure 12 WORKSHOP CALCULATION & SCIENCE-15.1 Concept of heat and temperature, effects of heat, difference between heat and temperature 2 Scales of temperature, Celsius, Fahrenheit, Kelvin and Conversion between scales of temperature 3 Temperature measuring instruments, types of thermometer, pyrometer and transmission of heat Conduction, convection and radiation 4 Co-efficient of linear expansion and related problems with assignments 5 Problem of Heat loss and heat gain with assignments 6 Thermal conductivity and insulators 7 Boiling point and melting point of different metals and Nonmetals 8 Concept of pressure and its units in different system
VII. Basic Electricity: 1 Introduction and uses of electricity, molecule, atom, how electricity is produced, electric current AC, DC and their comparison, voltage, resistance and their units 2 Conductor, Insulator, types of connections- Series and Parallel, Ohm's Law, relation between VIR & related problems 3 Electrical power, energy and their units, calculation with assignments 4 Magnetic induction, self and mutual inductance and EMF generation 5 Electrical Power, HP, Energy and units of electrical energy
VIII. Mensuration: 1 Area and perimeter of square, rectangle and parallelogram 2 Area an Perimeter of Triangle 3 Area and Perimeter of Circle, Semi-circle, circular ring, sector of circle, hexagon and ellipse 4 Surface area and Volume of solids- cube, cuboids, cylinder, sphere and hollow cylinder 5 Finding lateral surface area, total surface area and capacity in liters of hexagonal, conical and cylindrical shaped vessels
IX. Levers and Simple Machines 6 1 Simple machines, Effort and load, mechanical advantage, velocity ratio, efficiency of machine, relation between efficiency, velocity ratio and mechanical advantage 2 Lever and its types
X. Trigonometry: 1 Measurement of Angie, Trigonometrical Ratios, Trigonometric Table 2 Trigonometry-Application in calculating height and distance (Simple Applications)
Friction: 1 Advantages and disadvantages, Laws of friction, co- efficient of friction, angle of friction, simple problems related to friction 2 Friction - Lubrication 3 Co- efficient of friction, application and effects of friction in workshop practice
II. Centre of Gravity: 1 Centre of gravity and its practical application
III. Area of cut-out regular surfaces and area of irregular surfaces: 1 Area of cut-out regular surfaces - circle, segment and sector of circle 2 Related problems of area of cut out regular surfaces circle, segment and sector of circle 3 Area of irregular surfaces and application related to shop problems
IV. Algebra, Addition, Subtraction, Multiplication & Divisions 2 Algebra Theory of indices, Algebraic formula, related problems
V. Elasticity: 1 Elastic, plastic materials, stress, strains and their units and young modulus 2 Ultimate stress and working stress
VI. Heat Treatment: 1 Heat treatment and advantages 2. Different heat treatment process - Hardening, Tempering, Annealing, Normalising, Case Hardening
VII. Profit and Loss: 1 Simple problems on profit & loss: Simple and compound interest
VIII. Estimation and Costing: 1 Simple estimation of the requirement of material etc., as applicable to the trade 2 Problems on estimation and costing
· Engineering Drawing-Introduction to Engineering Drawing and Drawing Instruments - Conventions.
· Viewing of engineering drawing sheets. Method of Folding of printed Drawing sheet as per BIS SP: 46-2003
2. Drawing Instrument Drawing board, T-square, Drafter (Drafting M/c), Set squares, Protector, Drawing Instrument Box (Compass, Dividers, Scale, Diagonal Scales etc.), pencils of different grades, Drawing pins/ Clips.
3. Free hand drawing of Lines, polygons, ellipse etc. Geometrical figures and blocks with dimension Transferring measurement from the given object to the free hand sketches.. Solid objects Cube, Cuboids, Cone, Prism, Pyramid, Frustum of Cone with dimensions. Free hand drawing of hand tools and measuring tools, simple fasteners (nuts, bolts, rivets etc.) trade related sketches
4. Lines Definition, types and applications in drawing as per BIS: 46-2003 Classification of lines (Hidden, centre, construction, extension, Dimension, Section) Drawing lines of given length (Straight, curved) Drawing of parallel lines, perpendicular line Methods of Division of line segment
5. Drawing of Geometrical figures: Definition, nomenclature and practice of Angle: Measurement and its types, method of bisecting. Triangle: different types Rectangle, Square, Rhombus, Parallelogram. Circle and its elements Different polygon and their values of included angles. Inscribed and circumscribed polygons 8
6. Lettering & Numbering Single Stroke, Double Stroke, Inclined.
7.. Dimensioning and its Practice Definition, types and methods of dimensioning (functional, nonfunctional and auxiliary) Position of dimensioning (Unidirectional, Aligned) 7 Types of arrowhead Leader line with text Symbols preceding the value of dimension and dimensional tolerance.
8. Sizes and layout of drawing sheets Selection of sizes Title Block, its position and content Item Reference on Drawing Sheet (Item list)
9. Method of presentation of Engg.Drawing Pictorial View.Orthographic. View Isometric View
10. Symbolic representation different symbols used in the trades. Fastener (Rivets, Bolts and Nuts) Bars and profile sections Weld, Brazed and soldered joints Electrical and. electronics element Piping joints and fitting
11. Projections Concept of axes plane and quadrant. Orthographic projections Method of first angle and third angle projections (definition and difference) Symbol of 1st angle and 3rd angle projection in 3rd angle.
12. Orthographic projection from isometric projection 13. Reading of fabrication drawing.
1. Construction of scales and diagonal scales 2. Conic sections (Ellipse and Parabola) 3. Sketches of nuts, bolt,screw thread, different types of locking devices e.g. Double nut, Castle nut, Pin, etc. 4. Sketches of foundation 5.Rivets and rivetted joints, welded joints 6.Sketches of pipes and pipe joints 7. Assembly view of Vee blocks,
· Bush & Bearing, Different types of Coupling viz., Muff coupling, Half Lap Coupling, Flange coupling, etc. Simple work holding device e.g. vice Drawing details of two mating blocks and assembled view 8. Sketch of shaft and pulley, belt, gear, gear drives 1.Sign and Symbols of Electrical, Electronics and related trades 2. Sketch of Electrical and Electronics/trade related components 3. Electrical and Electronics wiring diagram/ trade related Layout diagram 4. Electrical earthing diagram Drawing the schematic diagram of plate and pipe earthing. 5. Electrical, Electronics/ trade related circuit diagram 6. Block diagram of Instruments/ equipment of related trades
